|
Bird Feeder Plans While any components can be utilized to produce a bird feeder the lap siding should really be manufactured from cedar wood. Cedar is resistant to rot and might withstand harsh weather circumstances for a lot of many years with out sealing or painting. All measurements to the Bird Feeder Plans are in inches Development Elements Qty. Lumber 1 3/4 x 16 x 16 plywood scrap 1 3/4 x 6 prevent moulding 1 8 x 10 cedar lap siding 1 1 x 2 x eight cedar 1 1 diameter x three dowel Cutting List Key Part Dimension Pcs. Material A Base 3/4 x 16 x 16 1 Plywood B Post 3/4 x 3/4 x 7 1/4 4 Cedar C Box side 5/16 x 7 1/4 4 Cedar siding D Ledge side 3/4 x one 1/2 x 17 1/2 2 Cedar E Ledge end 3/4 x 1 1/2 x 16 2 Cedar F Roof panel 5/16 x 7 1/4 x 20 2 Cedar siding G Ridge pole 1 diameter X 20 1 Dowel Other Products 1/4 diameter Threaded, galvanized or brass rod with matching nut and washer Wood glue Sizzling melt glue 4d widespread nails, rigid acrylic or plastic The Base Exterior grade plywood will do the job truly properly. Lower the plywood base (A) from 3/4" thick plywood. Draw diagonal lines from corner to corner to seek out the center from the square base. Measure and mark a 6 square inside the middle on the base. This can be the eventual place of one's feeder box. Drill a 1/4" hole with the center of the base. Measure in in direction of centre 3/8" from each corner from the six square and mark just about every stage. Drill 1/16" diameter pilot hoes appropriate from the base. Feeder Box Preparation The posts and the box sides will kind the walls from the feeder box. The vertical grooves while in the box sides will let you check the foods level. Little arc cuts within the bottom of your box sides controls the movement of meals by to the feeding area. Minimize the posts (B) to size from 3/4 square cedar stop moulding. Cut two 6" broad box sides (C) from 8" cedar lap siding. Cut two a lot more panels about 7" wide that will be trimmed to stick to the lap-siding bevels. Lower a slot in just about every box side that could be applied for viewing. This is reached by drilling two 1/2" diameter starter holes for a jigsaw blade along the centre of every single box side. Make the holes 2" from the top and bottom. Connect the starter holes by cutting using a jigsaw to cut the slots. Employing a jigsaw reduce a 1/2" deep arc to the bottom off every box side. Commence the cuts 1 1/2" from each and every end. Use a drum sander mounted on a power drill to smooth out the arcs. Minimize strips of clear acrylic or plastic a little bit much larger than the viewing slots. Use scorching glue to attach the strips behind the slots within the within faces of your box sides. Tape box sides together right into a box form so that you can mark the cutting lines for trimming two box sides to follow the siding bevel. (Broad ends of bevelling need to all be flush.) Trace the siding profile onto the inside faces from the two box ends. Take the box apart and reduce along the profile lines applying a jigsaw. Assembling the Feeder Box Use some wood glue to the posts trying to keep them flush with all the within edges about the box sides. (Clamp till dry) Glue the untrimmed box sides towards the posts. (Clamp until eventually dry) Base Frame Installation Seal edges with the base ahead of attaching the frame. Reduce the ledge sides (D) and ledge ends (E) from one x two cedar. (This may be your frame that extends throughout the base so that the foods stays within the feeder.) Glue and attach ledge pieces so bottoms are flush together with the floor from the base. Use 4d widespread nails to reinforce the joint. Attaching the Base Use a spacer to assist align the box square for the base. Align the assembled feeder box with all the 6" square drawn to the base. Applying these lines for reference glue the box for the base. Turn the assembly upside down. Attach the base to the feeder box by driving 4d galvanized popular nails from the pre drilled pilot holes from the base along with the posts within the feeder box. Build the Roof Lower ridge pole (G) from a 1" diameter dowel. Cut roof panels (F) from 8" siding. Lay panels on your work surface so the wide ends butt together. Slip a 1" thick spacer 2" in from each of the narrow ends to create the roof pitch. Implement hot glue to the seam concerning the panels. Press the ridge pole into the seam to reinforce the roof just before glue hardens. Leave for 15 minutes for glue to harden. Set roof down so the ends of the ridge pole every rest on the two x 4 block. Drill 3/8" diameter holes from the roof and ridge pole, 1" on every side from the mid-point with the ridge. Working with a jigsaw connect the two holes, cutting on both sides of your holes to build a 2" lengthy slot. Reduce the 1/4" diameter threaded rod to 16" in length. Use pliers to bend a one 1/2" diameter loop in a single finish of the rod. Thread the unbent finish with the rod throughout the slot from the roof and also the hole while in the base. Spin the rod loop making it perpendicular to your roof ridge. Tighten a washer and nut onto the end on the rod. (Allow it to be loose enough that the loop may be spun with reasonable energy.) Touch-ups Sand surfaces until eventually smooth. You could leave it purely natural or apply a finish of one's option that may be not toxic to birds If you have followed these Bird Feeder Plans to a tee, then you'll be making a whole lot of birds extremely joyful.
Related Articles -
Bird, Feeder, Plans,
| 
