 Fly ash drying plant
Fly ash drying plant applies to fly ash, phosphogypsum and titanium gypsum etc. Industry dust, waste residue drying. Fly ash drying plant is designed by the features of early moisture is higher than other materials; the proportion is less than other materials, big flow ability during dry process. It is mainly used for building materials and chemtry production in the fly ash, clay, slag, coal, ore drying etc. It is composed of three concentric circles of different diameters embedded in each other combination as the main part. The main art rotates the four tugs5 on both sides through the two tyres4. The advantages of the fly ash drying plant: 1. The investment required is 1/6 of the imported products. 2. It will ensure you the final material a moisture below 0.5% which is the first product of ash and slag product line. 3. Cylinder self-insulation thermal efficiency as high as 80% (traditional monocular dryer thermal efficiency was only 35%) to improve thermal efficiency of 45%. 4. Fuel, kerosene vapor applicable. 20mm below the block to dry powder material feed pellets. 5. Dryer than the monocular area of about 50% reduction, 50% reduction in civil engineering, power consumption decreased to 60%. 6. Use and manufacture than ordinary steel, alloy steel wear plate 4 times. 7. Can be customized easily control the required final moisture indicator. 8. Outlet temperature is low, dust removal device a long time. 9. The size of gears without using the tugs turn. Design system of fly ash drying plant 1. Control the early moisture content: The moisture of wet fly ash drying plant which just discharged from the power plant is in commonly around 45%. If dry the fly ash at once, the production cost is higer, it will form bigger pressure to the equipment. If pile up at a draughty area for about 15 days, the moisture of fy ash reduced to about 20%, then handle the materials is a better way. 2. The selection of dust collector. Because of fine fly ash particle, light density, in negative pressure state after drying, it is easy to take away by airflow, lead to the fluid media change, and the dusty gas moisture is bigger. 3. Dry materials conveying equipment should pay attention to seal. 4. The selection of hot air stove. Hot air stove should be choosed high efficiency, fully burn poor quality coal, convenient operation of the furnace type. Fly ash electrostatic separator High voltage fly ash electrostatic separator(also called fly ash static separator) is to utilize the difference of the electric conductivity to separate the materials under the function of electrical power andmechanical force in the multiple power plates which combine the high voltage corona field with the high static field. To strengthen the magnetism of the static electrode of the conductor, while strengthen the repellant of the non-conductor. Applications Of The flay ash Electrostatic Separator: 1. The complete sets of equipment of the wastealuminum-plastic separator and the waste electronic circuit. With the same separation principle: the separation purity can achieve more than99%; 2. The separation of the scheelite and the cassiterite; 3. The separation of the magnetite, hematite, chromite, manganese ore; and the separation of the tantalum-niobium ore, titanium iron ore, rutile, monazite; 4. Separate the metallic extraction of the other metallic and non-metallic mixture; 5. Separate the aluminum-plastic shavings materials (for example PVC aluminum-plastic shavings, the separation of the aluminum and plastic of the aluminum-plastic windows and doors); 6. The separation of the copper-plastic compound and the copper-plastic mixture (the copper recycling of theelectronic circuit board, the recycling of the copper-plastic of the PVC wire and winding displacement; 7. The separation of the quartz, feldspar and the separation of graphite, diamond, apatite, coal and asbestos; 8. The extractionof carbon of the fly ash; 9. The selection of the food and other grains to remove the impurities; 10. The selection of gold. Fly ash drying plant and electrostatic separator Manufacturers Morocco Crusher manufacturers provides the high quality service for the clients. Before the purchase, we will sendengineers and technicians freely to the producing site to plan the field, design the best process and project. After the purchase, we will freely send after sale service stuff to the site to direct the clients to install and adjust, and to help clients plan and manage the equipment until to fulfill the clients' satisfaction.
Related Articles -
fly ash drying plant, fly ash electrostatic separator, Morocco Crusher manufacturers,
| 
