Due to the special nature of the office space, we have to take a long time to keep the mind fresh, we should keep comfortable and peaceful state of mind and work efficiently without feeling tired. The office generally occupies the highest utilization rate in the daytime, the lighting of the office space is usually based on the needs of the office functions, at the same time we should take full advantage of natural light with artificial lighting, in order to maintain stability, reasonable, comfortable, healthy light environment. The purpose of lighting is to create a good working environment, meet the illumination requirements, uniform illumination is to reduce stroboscopic effect of light and glare and reduce visual fatigue level of the office staff. Therefore we should use cool light color, often from the 4200 to 5300K color temperature closer to the lighting of the morning, to remain calm, cool head. The bare lamp ceiling installation can be used and metal reflective fluorescent lifting can be used, office often use aluminum reflector grille fluorescent light embedded in the ceiling installation. Office lighting requirements 1, select the appropriate light source color temperature and color rendering index, in the office generally choose 4000K color temperature, color rendering index Ra = 75. 2 lighting levels: different environments, different places, lighting requirements vary. The office space illumination shall meet the requirements for 500-1000lx. 3,Lighting uniformity: reasonable arrangement of lamps, the illumination uniformity, the Office of the maximum, minimum illumination and the average illuminance is less than 1/3 of the average illumination. 4, comfort and glare control: too high brightness or excessive brightness ratio in the field of vision will make us feel dazzling glare. Limit the brightness of the light source and rational arrangement of the light source are the main measures to prevent glare Such as making the light source in the line of sight of more than 45 degrees is to form the shielding angle or opaque material to block the light source. 5, security: the main consideration of the safety of the lamp structure, electrical safety, lighting compliance with national standards, whether passes the 3C certification. 6, energy saving and environmental protection: the choice of high luminous efficiency light source, high efficiency, long life, in reasonable light fixtures, high-performance, long-life accessories. Light distribution generally opt for the bat-wing light distribution, uniform light intensity distribution of a wide. Introduction to traditional fluorescent Fluorescent lamps, also is known as fluorescent lamps. Fluorescent structure and function: both ends of the fluorescent lamps have a filament inside the tube which filled with a small amount of argon and thin mercury vapor. Phosphor is coated on the inner wall of the lamp. Ultraviolet light is formed when gas between the two filament is conducted so that the phosphor glows softly visible light. The characteristics of fluorescent work: when the lamp is ignited,which requires high voltage, lamp is filled with some special gas, phosphor is also coated in the wall of the tube, which produces light after power as a result of the discharge. Fluorescent tube has the filament on both ends, wall coated with a thin uniform layer of phosphor. Tube is evacuated and filled with a small amount of inert gas simultaneous inject a small amount of liquid silver. Inductive ballast when the coil current changes in the coil will cause the change of the magnetic flux, thereby generating an induced electromotive force, its direction opposite to the direction of the current, thereby preventing the current change. LED tube light introduction LED tube light has the same Dimensions caliber as the traditional fluorescent lamp, there are four kinds of 600mm, 900mm and 1200mm, 1500mm in length, the power is 9W, 14W, 18W, and 25W, Actual power consumption of 20W raditional fluorescent is about 53W , Actual power of 40W traditional fluorescent consumption is about 68W; 9W LED tube brightness is brighter than 18W fluorescent light, 18W LED tube light is even brighter than the traditional 40W fluorescent lamp, LED tuber light has softer light and is more easily accepted. Service Life is 30,000 -5 million hours .Its supply voltage is AC85V-260V (AC), without starter and ballast, can quick start,has low power, no flash, is not easy to visual fatigue. It has not only more super energy,but has environmentally friendly advantage. It is the mainly product which replace the traditional fluorescent products. The advantages of LED tube light in the office lighting 1, green lighting, protect the earth Traditional fluorescent lamp contains large amounts of mercury vapor, when broken,mercury vapor will evaporate into the atmosphere. LED tube light does not use mercury and LED products do not contain lead, play a protective effect on the environment. 2, high efficiency light-emitting and reduce losses The traditional lamp emitting direction is 360 degrees, the LED lamps are directional light-emitting, dose not cause the loss of light. 3, quiet and comfortable, no noise LED lamps do not produce noise, suitable for the use of sophisticated electronic equipment,such as the occasion of the library, office and the like. 4, soft light, protect your eyes Traditional fluorescent lamp use AC, it has 100-120 times per second strobe. LED lamps directly convert AC to DC ,it has no flicker so that can protect our eyes. 5, no UV, no mosquitoes LED lamps do not produce ultraviolet light, it is not the same as traditional lamps,which have a lot of mosquitoes around the light source side. The interior will become more clean and sanitary and clean. 6, the voltage adjustable 80V-265V The traditional fluorescent lamp is lighted by high voltage rectifier release, you can not light when the voltage is lowered. LED lamps can be lit within a certain range of voltage, also adjust the brightness. 7, energy saving longer life LED fluorescent lamp power consumption is half of the traditional fluorescent lamp, life expectancy is 10 times that of traditional fluorescent lamp, long-term use without having to replace, reduce labor costs. More suitable for the occasion difficult to replace. 8, robust, secure, long-term use. LED tube light uses epoxy resin instead of conventional glass, it is more robust, secure, and even when dropped on the floor ,LED is not easily damaged, can use safely. We have no reason to refuse such perfect light,with the arouse of environmental protection and "low-carbon wave",it just is the most suitable for us to raise work efficiency ,contact with www.lead-lighting.com for more unexpected.
Related Articles -
LED tube light, lighting, Office lighting, Fluorescent lamps, energy saving, environmental protection,
|