How to Install a LED Light on a License Plate The use of LEDs is quickly taking over the vehicle lighting replacement aftermarket. Consumers have their pick of many options for rear vehicle brake lights and license plate replacement lighting. The easiest light to upgrade to an LED for a DIY project is the rear license plate lighting. Since the license plate bulb does not directly affect the safety of the vehicle, it is a good place to start for a first-time LED project Instructions 1 Switch on the vehicle's lights and visually inspect the rear license plate light bulb to verify the wiring is properly working. 2 Turn off the vehicle's lights. Remove the key from the ignition. 3.Remove the existing license plate light bulb. 4 Turn on the vehicle's lights. Place the negative (COM) lead of a digital multimeter in the base of the empty light bulb base. Place the positive lead from the multimeter in the opposite side of the light bulb base. Set the multimeter to test DC voltage and take a reading. Most vehicles are designed with license plate lighting with 12 volts. 5 Turn off the vehicle's lights. Cut the rear license plate light wiring at the light bulb base. 6 Calculate resistor size. The forward voltage and forward current specifications for the LED are needed. Look for these values on the manufacturer's website. Subtract the LED forward voltage from the supply voltage to get the voltage drop. Divide the voltage drop by the LED forward current value. Round up to the nearest standard resistor size. 7 Connect the resistor to the positive lead from the license plate wiring using a crimp connector. Either side of the resistor is acceptable since there is no positive or negative lead on a resistor. 8 Connect the positive lead of the LED to the other side of the resistor using a crimp connector. The LED positive side is the longer lead. 9 Connect the negative lead of the LED to the negative lead from the license plate wiring. The LED negative side is the shorter lead. 10 Place heat shrink wrap or electrical tape around exposed metal in the LED circuit protecting the LED from a short circuit. 11 Place the LED inside the rear license plate light housing. Squeeze some silicone caulk to fill in the opening where the LED wiring enters the light housing. Tips & Warnings Most small high-intensity LEDs have a forward voltage of approximately 3.4 volts and a forward current specification of 25 mA. Use a 1/2 watt resistor. dm8000 hd wholesale led light usb flash drive usb flash drive wholesale usb flash drive flash drive manufacturer led lighting LED Wall Wash light LED video pixels LED Digital Tube light LED Spot Light LED Point Light LED Under-ground Lighting LED Commerical Lighting LED ba?ador de pared LED píxel de luz Tubos LED luz llevada del punto LED punto de Luz lenovo cellphone LED Spotlights Buried LED Iluminación Comercial ????? ????? ??? ????? ???????????? ????? ???????? ???????????? ?????? Power supply for DM500C DM500S DM500T Remote control for DM600PVR DM7000 DM7020S DM7025 Power Supply for DM600PVR DM7000 DM7020S DM7025 dm8000 hd dreambox dm8000 dm 8000 hd dreambox 8000 dreambox dm7020 dm7020 HD dreambox 7020 dm7020 HD dreambox 7020 Dreambox dm800 HD Se dm800 hd se with Wifi dm800 hd pvr dreambox dm800 hd pvr cheap dreambox dm800 hd pvr http://www.dreamboxok.com/dm500si.html Dreambox dm500S satellite receiver http://www.dreamboxok.com/Dreambox-DM-500-S.html DreamboxDM 500 OEM http://www.dreamboxok.com/DM500-OEM.htm Dreambox DM500C http://www.dreamboxok.com/Dreambox-DM-500-C.html Dreambox DM500C OEM http://www.dreamboxok.com/dm500c-oem.html Dreambox DM500S OEM http://www.dreamboxok.com/dm500s-oem.html Dreambox DM500Si Silver http://www.dreamboxs.com/dm500si.htm Dreambox dm500Si black http://www.dreamboxok.com/dm500si-black.htm Dreambox dm 518S http://www.dreamboxs.com/dreambox-dm518s.html Dreambox DM500T http://www.dreamboxok.com/Dreambox-DM-500-T.html AzBox HD Elite
Related Articles -
led, light, wall, washer,
|