Electrodynamic
Early wattmeter on display at the Historic Archive and Museum of Mining in Pachuca, Mexico.
The traditional analog wattmeter is an electrodynamic instrument. The device consists of a pair of fixed coils, known as current coils, and a movable coil known as the potential coil.
The current coils connected in series with the circuit, while the potential coil is connected in parallel. Also, on analog wattmeters, the potential coil carries a needle that moves over a scale to indicate the measurement. A current flowing through the current coil generates an electromagnetic field around the coil. The strength of this field is proportional to the line current and in phase with it. The potential coil has, as a general rule, a high-value resistor connected in series with it to reduce the current that flows through it.
The result of this arrangement is that on a dc circuit, the deflection of the needle is proportional to both the current and the voltage, thus conforming to the equation W=VA or P=VI. On an ac circuit the deflection is proportional to the average instantaneous product of voltage and current, thus measuring true power, and possibly (depending on load characteristics) showing a different reading to that obtained by simply multiplying the readings showing on a stand-alone voltmeter and a stand-alone ammeter in the same circuit.
The two circuits of a wattmeter can be damaged by excessive current. The ammeter and voltmeter are both vulnerable to overheating in case of an overload, their pointers will be driven off scale but in the wattmeter, either or even both the current and potential circuits can overheat without the pointer approaching the end of the scale! This is because the position of the pointer depends on the power factor, voltage and current. Thus, a circuit with a low power factor will give a low reading on the wattmeter, even when both of its circuits are loaded to the maximum safety limit. Therefore, a wattmeter is rated not only in watts, but also in volts and amperes.
Electrodynamometer
Siemens electrodynamometer, circa 1910. F = Fixed coil, D = Movable coil, S = Spiral spring, T = Torsion head, MM = Mercury cups, I = Index needle.
An early current meter was the electrodynamometer. Used in the early 20th century, the Siemens electrodynamometer, for example, is a form of an electrodynamic ammeter, that has a fixed coil which is surrounded by another coil having its axis at right angles to that of the fixed coil. This second coil is suspended by a number of silk fibres, and to the coil is also attached a spiral spring the other end of which is fastened to a torsion head. If then the torsion head is twisted, the suspended coil experiences a torque and is displaced through and angle equal to that of the torsion head. The current can be passed into and out of the movable coil by permitting the ends of the coil to dip into two mercury cups.
If a current is passed through the fixed coil and movable coil in series with one another, the movable coil tends to displace itself so as to bring the axes of the coils, which are normally at right angles, more into the same direction. This tendency can be resisted by giving a twist to the torsion head and so applying to the movable coil through the spring a restoring torque, which opposes the torque due to the dynamic action of the currents. If then the torsion head is provided with an index needle, and also if the movable coil is provided with an indicating point, it is possible to measure the torsional angle through which the head must be twisted to bring the movable coil back to its zero position. In these circumstances, the torsional angle becomes a measure of the torque and therefore of the product of the strengths of the currents in the two coils, that is to say, of the square of the strength of the current passing through the two coils if they are joined up in series. The instrument can therefore be graduated by passing through it known and measured continuous currents, and it then becomes available for use with either continuous or alternating currents. The instrument can be provided with a curve or table showing the current corresponding to each angular displacement of the torsion head.
Electronic wattmeter
Electronics portal
Prodigit Model 2000MU (UK version), shown in use and displaying a reading of 10 Watts being consumed by the appliance.
Electronic wattmeters are used for direct, small power measurements or for power measurements at frequencies beyond the range of electrodynamometer-type instruments.
Digital
A modern digital electronic wattmeter/energy meter samples the voltage and current thousands of times a second. The average of the instantaneous voltage multiplied by the current is the true power. The true power divided by the apparent volt-amperes (VA) is the power factor. A computer circuit uses the sampled values to calculate RMS voltage, RMS current, VA, power (watts), power factor, and kilowatt-hours. The simple models display that information on LCD. More sophisticated models retain the information over an extended period of time, and can transmit it to field equipment or a central location.
Radio frequency
Instruments with moving coils can be calibrated for direct current or power frequency currents up to a few hundred Hz. At radio frequencies a common method is a rectifier circuit arranged to respond to current in a transmission line; the system is calibrated for the known circuit impedance.
See also
Wikimedia Commons has media related to: Wattmeters
Ammeter
Voltmeter
Power factor
Electricity meter
Kill A Watt
Cent-a-meter
The Energy Detective
References
Categories: Measuring instruments Electronic test equipment Electric powerHidden categories: Wikipedia articles incorporating text from the 1911 Encyclopdia Britannica I am an expert from China Manufacturers, usually analyzes all kind of industries situation, such as mitutoyo digital caliper , electronic digital caliper.
Related Articles -
mitutoyo digital caliper, electronic digital caliper,
|
