1. Q: incandescent lamps are not energy-saving product, why launch incandescent?
A: compared to incandescent lamps with energy saving, in some respects is still has some of the advantages of energy-saving lamps do not have, such as small size, light low-cost, excellent color rendering, working state without environmental temperature, without electronic components, no adverse effects on the power supply system and so on. In instrument lights, emergency lighting and decorative lighting products, energy saving lamps is still played by the irreplaceable role, therefore, to promote green energy-saving lamp lighting products, but also introduced some high-quality incandescent bulb, such as decorative for the love of such products, the customers choose.
2. Q: incandescent lights, the glass bubble in the emergence of a group of white smoke, a light to destroy what is the reason?
A: The main structural part of the incandescent lamp glass, glass, easy to transport, such as the process by moving the collision, vibration appear invisible small cracks and leaks. With every crack of air into the bulb, in a turn on the light, the filament at high temperature and oxygen in the air react to form smog, while the filament is blown, the lights light up on the off. Therefore, the light source products in the transportation, moving, and the replacement, the installation process should be handled with care to prevent rupture.
3. Q: After the incandescent filament is broken, took it a shake, catch a filament, why is brighter than the original?
A: Incandescent is the use of current flows through the filament, so that heat to the incandescent filament state of luminescence. When the filament and then take them off, the original filament length has been shortened, so the smaller the resistance of the filament. When the re-energized, the current flowing through the bulb more than the original, so more light bulbs. Since the current flowing through the bulb increased, so off and then catch the filament of this lamp also can not work over a long time, but also because the current is too large and not security. Therefore, we strongly recommend that users, damage the bulbs should be replaced after the new lights, but do not plan to facilitate such "waste re-use."
4. Q: Why my house is not on the starter fluorescent lamp blink?
A: The starter is not bright and fluorescent light, is generally caused by low voltage. Will work for a long time because of the lamp has reached the end of life, but difficult to start. Therefore, if the voltage is normal inspection shall be promptly replaced with new lamp, do not let the lamp has not started work in the state of burning ballast.
5. Q: red fluorescent both ends, but point does not shine, why?
A: If a new lamp, the wiring should first check whether the equipment is wrong; if the original light fixtures working properly, you should check the starter or the capacitance is short-circuit failure, the starter is the fusion of metal pieces, or e-town Current is invalid. No test tools can be an alternative method to the pilot. If proven starter and ballast are normal, it indicates that the lamp has reached end of life, should be replaced lamp.
6. Q: fluorescent lamp, the light was snake-like undulating or rolling, why?
A: The beginning of the new lamp lit, the lack of time due to the aging of the factory early in the light of this phenomenon within a few minutes. Then it will generally normal. If such a long time, should check the voltage is too high, whether the failure of ballast. Use of inferior lamps, may be in use.
7. Q: energy saving lamp lights, why the roots of a black plaque?
A: The energy-saving lamps in the work of the material is liquid mercury. Light did not light up when the mercury drops of liquid absorption in the filament on the gathering. Lighting point, the liquid mercury fever due to a sudden and massive evaporation of the filament to the glass wall, the formation of black spots of mercury. General work about ten minutes, black spots that naturally evaporation of mercury, to restore the white wall. This is a fluorescent lamp in the normal course of work.
8. Q: Why do energy saving light work for some time, the light color of pink?
A: This is caused because of lack of mercury lamp, the lamp manufacturing process is the adverse situation. Should replace the lamp pole.
9. Q: Why do some tube rolling in a little black pellets?
A: Because the use of liquid mercury in fluorescent lamps, will cause some environmental pollution. In order to reduce mercury pollution, while improving the performance of the lamp, the current use of some lamps in mercury and other metal alloys, were solid at room temperature, can reduce the mercury vapor pressure, also known as small round black tablets, school called amalgam. Is currently used in fluorescent in new materials.
10. Q: What is the so-called three-wavelength fluorescent lamp mean?
A: Some manufacturers call it a three-wavelength fluorescent lamp, the real is what we call the three-color fluorescent lamps. Three-color light-emitting fluorescent colors are mainly composed of red light (wavelength 610nm), green light (wavelength 540nm), blue light (wavelength 430nm) wavelength three basic colors. Therefore, some manufacturers also called three-wavelength fluorescent lamp. I am China Toys Suppliers writer, reports some information about decorating with seashells , wholesale christmas garland.
Related Articles -
decorating with seashells, wholesale christmas garland,
|
