|
Introduction EDC injection inline pump The mechanical fly-weight governors of inline and distributor diesel fuel injection pumps used to control fuel delivery under a variety of engine loads and conditions could no longer deal with the ever increasing demands for efficiency, emission control, power and fuel consumption. These demands are now primarily fulfilled by the Electronic Diesel Control EDC, the system which provides greater ability for precise measuring, data processing , operating environment flexibility and analysis to ensure efficient diesel engine operation. The EDC replaces the mechanical control governor with an electro-magnetic control device. System overview The EDC is divided into these main groups of components. Electronic sensors for registering operating conditions and changes. A wide array of physical inputs is converted into electrical signal outputs. Actuators or solenoids which convert the control unit's electrical output signal into mechanical control movement. ECM (Electronic Control Module ) or Engine ECU (Electronic Control Unit) with microprocessors which process information from various sensors in accordance with programmed software and outputs required electrical signals into actuators and solenoids. Components EDC accelerator pedal assembly Sensors Injection pump speed sensor - monitors pump rotational speed Fuel rack position sensor - monitors pump fuel rack position Charge air pressure sensor - measures pressure side of the turbocharger Fuel pressure sensor Air cleaner vacuum pressure sensor Engine position sensor Temperature sensors - measure various operating temperatures Intake temperature Charge air temperature Coolant temperature Fuel temperature Exhaust temperature (Pyrometer) Ambient temperature Vehicle speed sensor - monitors vehicle speed Brake pedal sensor - operates with cruise control, exhaust brake, idle control Clutch pedal sensor - operates with cruise control, exhaust brake, idle control Accelerator pedal sensor Driver input switches - cruise control, idle increase /decrease, engine/exhaust brake Electronic Control Unit EDC control unit The ECU collects and processes signals from various on-board sensors. An ECU electronic module contains microprocessors, memory units, analog to digital converters and output interface units. Depending upon the parameters, a number of different maps can be stored in the onboard memory. This allows the ECU to be tailored to the specific engine and vehicle requirements, depending on the application. The operating software of the ECU can be adapted for a wide variety of engines and vehicles without the necessity of hardware modification. The ECU is usually located in the cab or in certain cases, in a suitable position in the engine bay where additional environmental conditions might require cooling of the ECU as well as a requirement for better dust, heat and vibrations insulation . Actuators and Solenoids EDC pump actuator Electro-magnetic actuators are usually located on the fuel pump to transfer electrical signals into mechanical action in this case fuel rack actuator and or fuel stop solenoid which means that depending on requests from control unit full fuel or no fuel quantity. Operation The injection of fuel or the quantity of injected fuel has a decisive influence on engine starting, idling, power and emissions. The engine ECU is programmed ("mapped") with relevant data to where the fuel rack position has an equivalent signal for the amount of fuel being injected. The driver requests the torque or engine speed requirements via accelerator pedal potentiometer thereby sending a signal to the engine ECU which then, depending on its mapping and data collected from various sensors, calculates in real time the quantity of injected fuel required, thus altering the fuel rack to the required position. The driver can also input additional commands such as idle speed increase to compensate e.g. for PTO operation which can be either variably set or has a preset speed which can be recalled. The road speed function can be used to evaluate vehicle speed and possibly activate a speed limiter (Heavy Vehicles), or maintain or restore a set speed (cruise control). Further functions can include exhaust brake operation which, when activated, will result in the fuel pump rack position being set to zero delivery or idle. The engine ECU can also interface with various other vehicle systems e.g. traction control and carries out self monitoring duties and self diagnostic functions to keep the system working at an optimal level. To ensure the safe operation in case of failure, the limp home mode functions are also integrated into the system, for e.g. should the pump speed sensor fail the ECU can use an alternator speed signal function for engine RPMs counter as a backup signal. Additional Functions Engine protection, cold start - when starting cold , engine rpms are limited. Engine protection, overheating - when overheating, to avoid damage the engine power output is limited. Remote engine shutdown - when auxiliary equipment is in use e.g. crane in case of rollover. Constant engine speed - the engine maintains set revs irrespective of load e.g. PTO operation References Diesel Fuel Injection published by Robert Bosch GmbH, 1994 ISBN 1-56091-542-0 Categories: Engine technology Engine fuel system technology I am an expert from skeletonmechanicalwatch.com, while we provides the quality product, such as skeleton mechanical watch Manufacturer , mechanical automatic watch, skeleton mechanical watch,and more.
Related Articles -
skeleton mechanical watch Manufacturer, mechanical automatic watch,
|
