For we introduce the next several Offset printing Common solutions to small problems:
1. To prevent the ink barrel ink crust
Ink stored in the open after a period of time, the surface layer of fat often hard knot ink skin, use must be thrown out. Over time, a considerable amount of wasted ink. We use shrinkage Package Paper covered in ink and the ink above its surface close to sealing. It is not no contact with the air oxidation crust waste. If time is short, then, more convenient way is to add water in the ink barrel, the principle is the same ink in contact with air to prevent the crust caused by waste.
2. Refueling small orifices fl Printing Operators have had this experience, equipment maintenance, the often vulnerable because of too much fuel or fuel oil viscosity due to improper printing products, sticky dirt and other production failure, in some places due to the machine Design Reasons, difficult to access conventional oil or fuel is not in place; this sewing machine oiler to the braces can be used, sold uranium, injection hole, machine the parts to fuel, this method can guarantee oil Di: lN-bit and will not be over oil leakage occurred more than splashing, dripping, causing waste printed materials, convenience and fuel economy. For press or machine inside wall below the hard to reach and the need for refueling site, available 8 support wire or other slender object, one end wrapped in its sponge dipped after the amount of lubricating oil, inserted into the printing press hard to get parts, but also lubrication where needed oiling.
3. India big field tips Printing workers have such experience: India big field frequently not full of ink printed materials, different shades, sticky dirty, sticky paper, rubber, printed materials are white, ink skin, paper, wool and so on. Seriously affect the printing quality and duration. We usually estimate the total ink volume of printed materials, ink tank as an added enough, add the appropriate ink to the viscosity, increase the ink dry oil flow and to avoid the middle of the ink viscosity caused by varying the size of the next ink do not result in different shades of ink, printing front, with clean cotton cloth coated with glycerin gently wipe the edges of the paper pile wool, paper, and then on the feeding station ready to print. Clean impurities left after the paper does not affect the quality of the field part of the ink. Printing machinery for the usual 60-70% rate of uniform printing inks can guarantee the normal delivery. India ink product line, sometimes for the plate on the ground there some eye of a needle, white face of this situation, only in the amount of oil rubbed fingers, rubbed eye of a needle plate part, to guarantee normal printing.
4. The use of waste reduction page car wash, wash rubber time Paul Edition
Stage in the feeding stacks of paper placed before waste put 20 pages, and then formally put the printing paper, when living conditions began to waste printed page when finished, will be torn off and the ink roller printing press, the water still rolls down , all waste will be printed on completion. The page can waste would remain in the plates and rubber ink away. Thus, cleaning the rubber on the much simpler plane plate can be rubbed directly without solvents to clean plastic protection version. Improve productivity.
5. Use version of margins in record
Offset PS version There are gaps around the edges, you can take advantage of these empty sites, do all the pieces of information about live records. Use a tape, recorded live parts printed number, date, ink color. Put version of method (positive and negative print since the reprint, large reproduction), color order, printed and other relevant information and data, and then paste in the Indian version of this tape space printing down. Print crew can operate a glance these records to avoid errors.
6. Blanket Use Each machine to prepare two sets of blankets, printing timing length according to ease living conditions, flat screen, back and forth to replace the text version to use, demand higher, more sophisticated graphic products, with the new rubber seal text version of the old rubber, rubber unload to clean rubber cleaning up after hang drying, long service life. Over the past year can save a lot of blankets.
7. Ink roller ink deal overnight
General, if the offset roller down more than 4 hours should be clean, otherwise ink solidified crust damaged ink roller of the transfer, absorption of ink, but sometimes due to special reasons, such as power failures, and can not be a bad time washing machine , and another Indian living conditions, they can transfer roller in the machine at the top of the horizontal surface of drops of some rubber or ink roller cleaning agent, and then start the machine to run 2-3 minutes, time that the light of the ink will be relaxed , inking Jii page N, the printed ink cleaner product line. I am a professional writer from China Bags Wholesale, which contains a great deal of information about steel tread plate , metal stair treads, welcome to visit!
Related Articles -
steel tread plate, metal stair treads,
|
