|
Thermostatic mixer works: the outlet valve in the thermostat with a thermal component, using a temperature device characteristics to promote the spool valve movement, block or open hot and cold water inlet in the block cold water, while open water, when the temperature control knob to a certain temperature, into the outlet of the hot and cold water also will automatically change in proportion to the output water temperature is always constant. Thermostat knob to between 35 -65 in any setting, thermostatic mixing water will automatically maintain the set water temperature. Faucet Temperature tap the market to use more memory alloy, paraffin, regulator valve to achieve the temperature effect in three ways, in general, the leading memory alloy temperature sensor to temperature change is faster, the temperature deviation is small, a constant temperature faucet preferred. Temperature leading to the production process require higher is recommended for larger brands to have quality assurance. Identification of product quality tap 1, visual Plating surface: a good smooth surface without leading spots, no plated flower, pinholes, blisters and other defects; vice versa counter. Coating: good thick lead plating, bright color; the other hand the leading thin coating, the color gray. 2, hand touch Hand touch no burr; gently moving the handle should be light and flexible, non-blocking sense; check whether the various components assembled in close, no loose feeling. 3, check Supporting parts are complete inspection, common faucet parts are: hoses, plastic Washer , Showers, drainage, cripple, decorative caps. Use and maintenance Use the constant temperature faucet, the light off a light, not too much force, excessive force is often damaged valve stem to move off. Used for a period of time, leading the surface pollution linked to, or dirt as the water flow may result in reduced or temperature control out of control, when required to maintain. 1, the leading surface pollution linked to: Wipe with a soft cotton cloth general can, as people face the same. In order to maintain the leading surface brightness, should always use Ruanmian cloth wipe neutral detergent solution, rinse water can generally be cleaned every 32 days on a health, pay attention to the leading surface bogey bogey acid base. 2, internal maintenance: (1) close the cold water inlet valve. (2) with Wrench Turn the water faucet on both sides Nut Remove the wire mesh gasket 11, check valve 13, cleaning the surface dirt screen, check valve is working properly, if not normal, to be replaced. (3) with 3MM hex wrench unscrew Screw 1 Handle Round 4, until the hand wheel and pull out the valve core 2 with the leading case, cleaning the surface of filter cartridge 2 online dirt, and then let the thread spool on the main faucet holes at the hole, push the spool into the main body rotation screws. Temperature leading major shortcomings: 1, thermostatic bar It is understood that in 2003 the factory was doing very little of these products require constant temperature valve plant must use a stick made of the temperature. However, domestic production since 2004 more than the factory thermostat stick up. As the pulpy material is equipped with a high temperature process requirements, the author of the thermostat on the market today is also suspected of leading life. Another package in the temperature (mashed temperature materials) and a rubber plunger between the film, and rubber membrane relative to the temperature around the package is fixed, due to thermal expansion and contraction and the temperature materials Spring When the role of causing concave rubber film, when the convex, so easily lead to rupture of rubber membrane, causing leakage of temperature materials, and is rapidly oxidized. Thermostatic valve ultimately useless. 2, check valve Many of the leading factory production temperature, check valve is Plastic Material production. As always in pressure and temperature among the plastic valve easily aging, and easy to damage. General Life does not exceed 2 years. 3, water pressure Constant temperature faucet water pressure have certain requirements, the general requirements in the 0.1-0.5Mp, there are cold, hot water pressure can not be too much. If the temperature of hot water pressure is less than 0.05 leading the following is recommended not to buy the leading temperature. 4, temperature General requirements of hot water temperature 49-80 degrees. 5, water quality If water quality is poor, the piston valve easier to get stuck, resulting in constant failure. Another important point is that if the hot water from gas water heater, if the water heater thermostat faucet flow regulation and inconsistent temperature will be a great risk of losing the leading role, please purchase must pay attention! We are high quality suppliers, our products such as China Root Canal Files , Dental Laboratory Materials Manufacturer for oversee buyer. To know more, please visits Dental Screw Post.
Related Articles -
China Root Canal Files, Dental Laboratory Materials Manufacturer,
|
