|
To speed up the printing industry structure adjustment, standard printing and dyeing project access, printing and dyeing industry to promote energy conservation and elimination of backwardness, to promote sustainable development, printing and dyeing industry, according to relevant laws, regulations and industrial policies, the ministry in conjunction with relevant departments on the "quasi-printing and dyeing industry entry conditions "(Development and Reform Commission Notice No. 14 of 2008 released) was revised, the revised the" printing industry access (2010 revision), "public announcement. All departments and relevant enterprises in the printing record investment, construction and EIA approval, land supply, credit, quality, safety supervision, production operations and other work to the access conditions should be based. Annex: printing and dyeing industry access (2010 revision) 2? 1? On April 11 Printing and dyeing industry access (2010 revision) To speed up the printing industry structure adjustment, promoting energy saving and emission reduction and sustainable development, in accordance with national laws, regulations and industrial policies, is released on the 2008 amendments to access printing and dyeing industry. A production company layout (A) of the various provinces, autonomous regions, municipalities directly under the departments concerned according to the resources Energy Conditions and market demand, scientific planning and dyeing industry. New or modified printing expansion project to meet the national industrial planning and industrial policy, the ecological environment of this region, planning and land use planning requirements. (B) of the State Council, national departments and provinces (autonomous regions and municipalities) under people's governments at scenic spots, nature reserves, drinking water protection areas and major rivers cross borders not within the provisions of the new printing project; has put into operation in the area of printing and dyeing production enterprises to the regional planning and the need to protect the ecological environment, according to the law by closing, relocation, transfer, etc. out of date. (C) the lack of water or poor water quality in areas in principle, the new printing project. Water is relatively abundant new printing project area, the relevant local government departments to scientific planning and rational distribution must be concentrated in the industrial park construction, centralized heating and centralized treatment of pollutants. Lack of environmental capacity of areas to limit the development of printing and dyeing projects, new or expansion project with out backward production capacity within the region combined. Industrial park admission of foreign enterprises should be gradually moved, in situ rebuilding and expansion projects shall not increase emissions. Second, technology and equipment requirements (A) new or modified printing expansion project to use advanced technology, use of pollution intensity, energy saving Environmental protection Equipment, the main device parameters to achieve the online detection and control. Prohibited use include, "Industrial Restructuring Guiding Catalog" restricted category, out of the backward class production technology and equipment, limiting the use of more than 5 years of useful life and not meet energy saving requirements of the secondary pre-treatment, dyeing equipment. Expansion of new or modified general level dyeing production line to approach or reach the international advanced level [of cotton, chemical fiber and blended fabric dyeing project design and construction to implementation of the "printing plant design specification" (GB50426-2007)]. (B) new or modified printing expansion project should be preferred high efficiency, low consumption of continuous processing equipment and technology; continuous washing equipment has good sealing, and is equipped with counter-current, high efficiency washing and heat recovery; Batch liquor ratio dyeing machines to be able to meet the technical requirements below 1:8; Stenter device to a temperature, humidity and other main-line monitoring and control device parameters, with gas cleaning and heat recovery unit, box and the outer surface of insulation board Environmental temperature is not greater than 15 . (C) printing and dyeing enterprises to increase the technological transformation of existing efforts to phase out use of duration more than 15 years ago-processing equipment, hot air Stenter equipment, and liquor ratio greater than 1:10 in the batch dyeing machines, out of process long, high energy consumption, heavy pollution and outdated technologies. Support the use of advanced technologies to upgrade existing equipment and technology level, where backward production technology and equipment companies, must be allowed to combine with the elimination of backward Extension. 3, Quality and Management (A) of the printing and dyeing enterprises to develop and produce low consumption, low pollution to meet market demand of products, encourage adoption of new technologies, new processes, new equipment, new materials developed with independent intellectual property rights, high value-added Textile Products. Product quality to meet the national or industry standards, product qualification rate of 95% or more chemicals. (B) of the printing company should be a three-level energy use, Water Management, set up specialized agencies or personnel on energy, water, sewerage monitoring the situation and to establish management evaluation systems and statistical systems. (C) printing and dyeing enterprises to strengthen management, improve enterprise management system. Encourage enterprises to quality, environmental and occupational health management system certification, support for enterprise information management tool used to improve the efficiency and level of enterprise management. 4, resource consumption (A) new or modified printing expansion project and the fresh water consumption per unit quantity of water to meet specified requirements (see Table 1). (B) of the existing printing companies should speed up technological innovation, energy consumption per unit quantity of water and fresh water to meet specified requirements (see Table 2). Concerned about changes in business innovation process management to find new ideas?? Command of the 2010 special screen printing industry of China Development Forum "Zhen Xing Cup" 2009 China Top Ten selection screen printing special awards ceremony More exciting, please see We are high quality suppliers, our products such as Sintered Parts Manufacturer , Shock Pistons for oversee buyer. To know more, please visits Stainless Steel Cabinet Pulls.
Related Articles -
Sintered Parts Manufacturer, Shock Pistons,
|
