|
Electrical outlet installation is done properly, you need to cross check the entire process thoroughly. ">While you want to do residential wiring on your own, then learning about electrical outlet installation would be your first criteria. When you take proper precautions, then it becomes easier to install new electrical outlet step by step. First you need to find out that circuit breaker, which is feeding the old outlet. You need to reach the electrical service box at your home. You have to check whether location of circuit breakers is marked properly. If they are not properly marked then you have to put an effort to shut each circuit breaker one after another, just to check which outlet you are replacing. It is usually seen that most of the outlets run off of a 15 amp breakers so you have to mark those switches. You have to plug a light into the outlet and check whether it goes out while you switch the breaker. While outlet is not working properly, you need to check with circuit tester in order to see the wires to the outlet which will ensure that electricity is off. In order to trip the breaker, you could short against the black and white wire with an insulated screwdriver. Thought this way may not be the safest way to out the correct one. You can discard the front cover plate once you have the electricity shut off. You can pull out the old outlet by unscrewing it. At least two wires have to be connected to the outlet and while it is grounded circuit to the service box then it can be three in number. In that case, one wire has to be white while other has to be black and the ground one has to be copper. If you are an owner of an old house with an old Residential wiring , then most probably you have only two wires and colors may vary. But most commonly, they are supposed to be white and black. The white wire is also referred as the ground and it is also called as the neutral wire. The black wire or hot wire is meant for supplying electricity. But be cautious before removing any wire and you need to take a not on the old outlet so that it can be replaced with the new one. You have two options of connecting the wire – either you connect to the screws on each side or you can slide the wires into the back of the outlet in their correct slots. Once Electrical outlet installation is done properly, you need to cross check the entire process thoroughly. "> Residential wiring , then most probably you have only two wires and colors may vary. But most commonly, they are supposed to be white and black. The white wire is also referred as the ground and it is also called as the neutral wire. The black wire or hot wire is meant for supplying electricity. But be cautious before removing any wire and you need to take a not on the old outlet so that it can be replaced with the new one. You have two options of connecting the wire – either you connect to the screws on each side or you can slide the wires into the back of the outlet in their correct slots. Once Electrical outlet installation is done properly, you need to cross check the entire process thoroughly. ">While you want to do residential wiring on your own, then learning about electrical outlet installation would be your first criteria. When you take proper precautions, then it becomes easier to install new electrical outlet step by step. First you need to find out that circuit breaker, which is feeding the old outlet. You need to reach the electrical service box at your home. You have to check whether location of circuit breakers is marked properly. If they are not properly marked then you have to put an effort to shut each circuit breaker one after another, just to check which outlet you are replacing. It is usually seen that most of the outlets run off of a 15 amp breakers so you have to mark those switches. You have to plug a light into the outlet and check whether it goes out while you switch the breaker. While outlet is not working properly, you need to check with circuit tester in order to see the wires to the outlet which will ensure that electricity is off. In order to trip the breaker, you could short against the black and white wire with an insulated screwdriver. Thought this way may not be the safest way to out the correct one. You can discard the front cover plate once you have the electricity shut off. You can pull out the old outlet by unscrewing it. At least two wires have to be connected to the outlet and while it is grounded circuit to the service box then it can be three in number. In that case, one wire has to be white while other has to be black and the ground one has to be copper. If you are an owner of an old house with an old Residential wiring , then most probably you have only two wires and colors may vary. But most commonly, they are supposed to be white and black. The white wire is also referred as the ground and it is also called as the neutral wire. The black wire or hot wire is meant for supplying electricity. But be cautious before removing any wire and you need to take a not on the old outlet so that it can be replaced with the new one. You have two options of connecting the wire – either you connect to the screws on each side or you can slide the wires into the back of the outlet in their correct slots. Once Electrical outlet installation is done properly, you need to cross check the entire process thoroughly.
Related Articles -
Electrical outlet installation, Residential wiring,
| 
