Have you ever wondered if the drying contractor you were operating with about a water damage claim REALLY KNOWS what they were doing and why they are doing it?
If you haven't, YOU SHOULD!There is one method to make certain the drying technicians you benefit in your losses know what they are doing... See how they answer these questions! 1. What extraction tool do used? o When? There are many different types of extraction tools. The most commonly known is the "carpet cleaning wand". This wand comes with all truck installed units when they are purchased thus naturally it is actually the most well known. Should you are getting to dry the carpet and leaf inside place, you must have a automotive extractor which you ride. The carpet cleaning wand is only efficient about glue down carpet. It is much easier to extract then to evaporate and this might be why the extraction tool is so important. 2. How numerous CFM does your truck mount / handheld extraction unit have? Either a truck mount unit or a handheld extraction unit which can surpass a truck mount is preferred. This is furthermore important to know which for every foot of 2" cleaner hose you have connected you shed 1 CFM. Water could not be removed with a 1 ½" hose. If the hose is reduced by ½" the amount of cleaner is reduced by 1/3. It is very important when struggling to dry the carpet and leaf inside place. Whatever reduction inside cleaner usually lower the amount of water which is pulled out. This usually further boost the drying time. NOTE: IT IS 500% EASIER TO EXTRACT THAN IT IS TO EVAPORATE! 3. When do you float carpet and why do you need to float carpet? o If exiting the carpet inside a structure, how do you dry it? Floating carpet can influence it to delaminate or to fray at the ends. If carpet is permitted to jump up and down found on the finish strip, the ends usually fray and you simply purchased carpet. What if your renovation organization might dry carpet and leaf inside place and lower the cost of your claims. Reducing the cost of your claims is our objective. Since carpet and leaf is a lot of the cost about numerous claims, by drying the carpet and leaf inside place together with the remainder structure, you can dramatically lower the cost of your claims. Floating the carpet is a thing of the last and could almost not be done. It usually actually slow down the drying time by floating the carpet. 4. When is carpet many susceptible to delamination? o Wet or dry? Most of the time, delaminated carpet is the result of the way it is actually handled when sticky. Carpet is 70 - 80% weaker when it is actually sticky and thus it can delaminate quickly inside a water damage situation. If the carpet and leaf are left down to dry and not disturbed, the possibilities of delamination are almost no. There have been tests done by the carpet mills which display after acarpet has been sticky and dried, inside a fair amount of time, the carpet is stronger than before. 5. What form of dehumidifier(s) do used? o And why? There are four different kinds of dehumidifiers chosen in the renovation business. In my opinion, merely 2 of them can actually dry a structure fast. If among the first 2 style of dehumidifiers are employed it is actually a waste cash and time. 1. Standard Refrigerants - Homeowners and experts, inside several instances, employ low capacity standard refrigerants. These include not built for the excessive transportation included in commercial use. When temperature drop under 68°F, ice usually begin to shape found on the coils, because the heat drops, eliminating any dehumidification. These dehumidifiers are merely able of pulling the grains of wetness inside the drying chamber down to 55-60 gpp's (grains of wetness per pound of air). At this point, dehumidification usually stop. The vitality efficiency is regarding 2-3 pints per kilowatt. 2. Conventional Refrigerants - Conventional refrigerants have a "defrost" cycle. Heat pipes inside this substance are a pair of coils sandwiched about the evaporator of a refrigeration program. They contain substance and transfer heat about the evaporator without the employment of compressors or capillary tubes to avoid icing. The warm air which enters the evaporator is cooled by the first heat play. This assimilated heat moves to the 2nd heat play, which is cooled by the environment exiting the compressor. All this signifies is that the dehumidifier usually not freeze up inside temperature because low because 33°F. They work precisely like a standard refrigerants otherwise. They furthermore, can merely pull the gpp's down to 55-60. 3. Low Grain Refrigerants (LGR) - The incoming air is pre-cooled by re-directing air exiting the evaporator back through the inlet air chamber. This pre-cooling is what makes LGR's work thus efficiently. The heat transfer is accomplished without more vitality consumption. LGR's pull the grains of wetness down to 32-35 gpp's. They furthermore include a defrost cycle. There are two kinds of LGR's available now. Heat pipe shape with an energy efficiency of 3-5 pints/kilowatt and the recuperative shape with an energy efficiency of 5-7 pints/kilowatt. As you can tell, the recuperative shape is more efficient inside the amount of your energy it pulls and inside the amount of water it pulls. The LGR's with all the recuperative shape usually actually pull less electricity than many traditional dehumidifiers, blow more air, and pull more water. In 2005 the Phoenix Corporation came out with a Low Grain Refrigerant which can furthermore work efficiently inside excellent heat. The Phoenix 200 HT. It is the many efficient substance dehumidifier available now. In May 2006 Phoenix introduced a performance amplifier which usually sit over their 200 Max's and 200 HT's. Theperformance amplifier usually boost the efficiency of the dehumidifier from 40 to 400%. These 2 unique products together allows us to dry structures even quicker than you were before and tear up less of the structure inside the process. 4. Desiccant dehumidifiers - take water out inside the form of a fuel. Desiccants work right outside the drying chamber and inside cold temperature. Desiccants do not work well inside excellent temperature. They can pull the grains of wetness down to 10-15 gpp's or reduce. Many desiccants chosen in the renovation business contain silica serum. It is a highly absorbent chemical. Desiccants work well when drying a spider room, wooden floor, large structure, etc. When drying a crawlspace with a desiccant then you would not desire to certainly stress the crawlspace. Since desiccants can be put in place positive, negative, or simple you must know how and why to set one up properly. Even though there is no greater dehumidifier than a desiccant merely regarding 1% of the drying businesses own any. There are three leading reasons: o The price of purchasing desiccant is generally more expensive than the cost of many refrigerants. o The electrical requirements are usually such which they need an electrician for hook up. o The time it takes to put together a desiccant is of more than the time it takes to put together a refrigerant dehumidifier. 6. How do you figure out how much dehumidification you require? First off, you like to create because small of a drying chamber because potential thus that you can use the amount of equipment potential. It is done by the following: o Closing doors o Putting up Plastic to separate areas o Be sure all doors and windows are closed After creating a drying chamber then figure up the amount of cubic feet of air to be dried. You are able to then know what size and how numerous dehumidifiers usually be required to dry the work. There is a chart included found on the next page which provides the formula for figuring how many dehumidifiers and what kind are needed. 7. How do you figure out how numerous lovers are needed about a job? Fans could be located every 12 -16 feet inside a round motion about the area. They could be located because close to the wall because potential at a 45 degree angle. Doors could be removed within the hinges thus that air circulation does not receive trapped behind the doorway. When carpet is included one enthusiast can be located in the middle of the area about a stand pointing down. 8. What kind of meters are employed? o Floors o Sub-floors o Walls o Psychrometric Readings o Infrared Thermometer There are a range of meters available now. You are able to test building components with pinless meters or meters which have pins. The pinless meters are preferred considering they do not damage the wall inside the process of checkingfor wetness. There are also various other meters such as infrared thermometers, hygrometers, wetness probes for carpet, hammer probes for checking wooden floors, etc. A superior drying contractor need numerous different types of meters and know how to use them. 9. Do used psychrometrics about EVERY drying job? o If thus, what does psychrometry tell you regarding your job? Using psychrometrics about EVERY drying job usually tell you if the work is put in place to dry. It usually not tell you whether its dry or not. Should you are keeping a psychrometric chart about every job it usually tell you numerous different things: o Whether or not the dehumidifiers are pulling water and working properly o Should you have a drying chamber o Should you have sufficient equipment o Whether or not the A/C is pulling water o Shows how the equipment is performing about what exactly is happening outside and inside the unaffected areas 10. If there is moisture under vinyl, how do you dry it? o How do you dry behind plastic wallpaper or a plastic floor? To dry the ground it is in the plastic almost all of the times it is actually required to remove the plastic. To dry the wall behind plastic wallpaper, almost all of the time you need to remove it. However, occasionally you can get to the wall by removing the baseboards and blowing air up inside the wall. It usually even dry quicker in the event you can to let the environment out at the top of the wall. This allows the sticky air from the wall while you're blowing inside more dry air within the bottom, thus drying the wall extremely fast. BONUS: How often do you confirm your water damage jobs? It is important to confirm the jobs at the least once every 24 hours. There is lovers which need to be moved about and questions within the homeowner which need to be addressed. We check all water damage jobs at the least once a day. This includes weekends and holidays. Jobs which are close to us usually occasionally be checked 2 or 3 times a day. These jobs commonly dry quicker than a job across town. If a organization does nothing more you have earlier discussed they can all the same accelerate the work by just checking it daily.
Houston Water Damage
Related Articles -
water damage houston, houston water damage,
| 
