Industrial Mixing Equipment: 1. The mixer should be set in a flat position, square wooden paving the front and rear axles, the tire resting high overhead to avoid when starting walking around with security. 2. The mixer should impose secondary leakage protection. Before the power is turned on, you must carefully check the empty test switch is qualified or not. Commissioning should be tested during the rotational speed of the mixing drum is appropriate. Under normal circumstances, the proportion of empty speed is faster than charging speed around 2 to 3 rpm. If the differ is big, you shoud adjust the ratio between the movable wheel and the transmission wheel.
3. The mixing section part’ rotation direction should be consistent with the direction of the arrow; if not, the motor wiring should be corrected especially for the Vertical Mixers. 4. Check if the drive clutch and brake is flexible or not; the steel rope is damaged or not; the track pulley is good or not; and check the around environment and all parts’ lubrication. 5. After starting up, be careful that is all the parts of mixer are normal working or not. After shutdown, always check whether the mixer blades bent screw has knocked out or loose. 6. When the concrete mixer is completed or is expected to stop more than 1 hour, besides of cleaning the rest materials, putting stones and clear water into the shaking barrel and starting uo rotating, and clean out all the mortar sticked in the barrel. No water inside the barrel, in order to avoid the barrel or the leaf gets rust. Meanwhile remember to clean the mixing tube fouling as well, maske the machinery clean and in good condition. 7. After work or shut down without using, wind up its power and lock the switch box to ensure safety.
www.chemicalmixer.net has 10 years of professional manufacturing dyeing equipment qualifications. Constantly improve and perfect the product features, the introduction of new processing technology, absorb advanced technologies to all parts of the further modularization, standardization, automation. In addition to the main product mixer, plastic machine quality excellence, but also for customer needs, develop a multi-functional combination of models, enhance customer productivity.">Industrial Mixers and Blenders are used to mix or blend a wide range of materials used in different industries including the food, chemical, pharmaceutical, plastic and mineral industries. They are mainly used to mix different materials using different types of blades to make a good quality homogeneous mixture. Included are dry blending devices, paste mixing designs for high viscosity products and high shear models for emulsification, particle size reduction and homogenization. Industrial mixers range from laboratory to production line scale. Here are tips for safty use of Industrial Mixing Equipment: 1. The mixer should be set in a flat position, square wooden paving the front and rear axles, the tire resting high overhead to avoid when starting walking around with security. 2. The mixer should impose secondary leakage protection. Before the power is turned on, you must carefully check the empty test switch is qualified or not. Commissioning should be tested during the rotational speed of the mixing drum is appropriate. Under normal circumstances, the proportion of empty speed is faster than charging speed around 2 to 3 rpm. If the differ is big, you shoud adjust the ratio between the movable wheel and the transmission wheel.
3. The mixing section part’ rotation direction should be consistent with the direction of the arrow; if not, the motor wiring should be corrected especially for the Vertical Mixers. 4. Check if the drive clutch and brake is flexible or not; the steel rope is damaged or not; the track pulley is good or not; and check the around environment and all parts’ lubrication. 5. After starting up, be careful that is all the parts of mixer are normal working or not. After shutdown, always check whether the mixer blades bent screw has knocked out or loose. 6. When the concrete mixer is completed or is expected to stop more than 1 hour, besides of cleaning the rest materials, putting stones and clear water into the shaking barrel and starting uo rotating, and clean out all the mortar sticked in the barrel. No water inside the barrel, in order to avoid the barrel or the leaf gets rust. Meanwhile remember to clean the mixing tube fouling as well, maske the machinery clean and in good condition. 7. After work or shut down without using, wind up its power and lock the switch box to ensure safety.
www.chemicalmixer.net has 10 years of professional manufacturing dyeing equipment qualifications. Constantly improve and perfect the product features, the introduction of new processing technology, absorb advanced technologies to all parts of the further modularization, standardization, automation. In addition to the main product mixer, plastic machine quality excellence, but also for customer needs, develop a multi-functional combination of models, enhance customer productivity.
Related Articles -
export inspection agency, china quality control,
|
