|
|
|
Blower door - Motion Detectors - CCTV Wireless Camera by efvf vdvV
|
|
|
Blower door - Motion Detectors - CCTV Wireless Camera |
|
|
|
Business,Business News,Business Opportunities
|
|
Uses of blower-door testing Blower doors can be used in a variety of types of testing. These include (but are not limited to): NFPA Clean Agent Retention testing (this type of testing is usually described as a door fan test rather than a blower door test) Testing residential houses for air tightness Testing buildings for compliance with standards for energy efficiency, such as those by the Leadership in Energy and Environmental Design (LEED) and Passive House/Passivhaus. Testing building envelopes and window frames for water tightness and rain penetration How blower-door tests work A basic blower-door system includes three components: a calibrated fan, a door-panel system, and a device to measure fan flow and building pressure. The blower-door fan is temporarily sealed into an exterior doorway using the door-panel system. The fan is used to blow air into or out of the building, which creates a small pressure difference between inside and outside. This pressure difference forces air through all holes and penetrations in the building enclosure. The tighter the building (e.g. fewer holes), the less air is needed from the blower door fan to create a change in building pressure. Blower-door airtightness measurements are presented in a number of different formats, including but not limited to: Air flow CFM50 is defined as the air flow (in cubic feet per minute) needed to create a 50-pascal pressure change in the building envelope. CFM50 is one of the most basic measurements of airtightness. Air flow measurements are sometimes referenced to different building pressures such as 25 or 75 pascals. Air changes per hour at 50 pascals To compare relative airtightness of buildings, it is useful to normalize measurements for the size of the building. This allows easy comparison of various sized buildings to each other, or to program guidelines. One of the most common ways to normalize building airtightness is to calculate the number of times per hour the total volume of the enclosure is changed, when the enclosure is subjected to a 50-pascal pressure difference. To calculate air changes per hour, the total volume of the enclosure is required in addition to the CFM50 measurement. It is also common to use the building enclosure surface area to normalize airtightness measurements. A pressure of 50 Pa is equal to 0.2 inches (0.51 cm) of water column. Leakage area Leakage area estimates are a useful way to visualize the cumulative size of all leaks or holes in the building enclosure. Estimated leakage areas can also be used in infiltration models to estimate natural infiltration rates (i.e. the air change rate under natural weather conditions). To accurately estimate leakage areas, it is best to conduct the blower-door test over a wide range of building pressures (e.g. 60 Pa to 15 Pa). There are a variety of standard calculation methods used to calculate leakage areas. Leakage area per square area Leakage area estimates can also be normalized for the size of the enclosure being tested, For example, the LEED Green Building Rating System has set an airtightness standard for multifamily dwelling units of 1.25 square inches (8.1 cm2) of leakage area per 100 square feet (9.3 m2) of enclosure area, to control tobacco smoke between units. This is equal to 0.868cm/m. Manufacturers There are three main manufacturers of blower doors. Energy Conservatory makers of the Minneapolis Blower Door Infiltec Retrotec Energy Innovations Ltd. References ^ Siemens Building Technologies Home Energy Guide Categories: Heating, ventilating, and air conditioning The e-commerce company in China offers quality products such as Motion Detectors , CCTV Wireless Camera, and more. For more , please visit 3G Video Alarm today!
Related Articles -
Motion Detectors, CCTV Wireless Camera,
|
Rate This Article |
|
|
|
Do you Agree or Disagree? Have a Comment? POST IT!
Reader Opinions |
|
|
|
|
|
|
|
|
Author Login |
|
|
Advertiser Login
ADVERTISE HERE NOW!
Limited Time $60 Offer!
90 Days-1.5 Million Views
|
|
GENE MYERS
Author of four books and two screenplays; frequent magazine contributor. I have four other books "in...more
|
|
|
|
|
TIM FAY
After 60-plus years of living, I am just trying to pass down some of the information that I have lea...more
|
|
|
|
|
ADRIAN JOELE
I have been involved in nutrition and weight management for over 12 years and I like to share my kn...more
|
|
|
|
|
LAURA JEEVES
At LeadGenerators, we specialise in content-led Online Marketing Strategies for our clients in the t...more
|
|
|
|
|
STEPHEN BYE
Steve Bye is currently a fiction writer, who published his first novel, ‘Looking Forward Through the...more
|
|
|
|
|
ALEX BELSEY
I am the editor of QUAY Magazine, a B2B publication based in the South West of the UK. I am also the...more
|
|
|
|
|
SUSAN FRIESEN
Located in the lower mainland of B.C., Susan Friesen is a visionary brand strategist, entrepreneur, ...more
|
|
|
|
|
SHALINI MITTAL
A postgraduate in Fashion Technology. Shalini is a writer at heart! Writing for her is an expression...more
|
|
|
|
|
JAMES KENNY
James is a Research Enthusiast that focuses on the understanding of how things work and can be impro...more
|
|
|
|