|
|
|
How to apply Fiberglass and Gelcoat - Tips for Boat Hull Repair by Web Master
|
|
|
How to apply Fiberglass and Gelcoat - Tips for Boat Hull Repair by WEB MASTER
|
|
Article Posted: 09/27/2012 |
Article Views: 69 |
Articles Written: 1 |
Word Count: 549 |
Article Votes: 0 |
|
How to apply Fiberglass and Gelcoat - Tips for Boat Hull Repair |
|
|
|
Business
|
|
Spaying gelcoat When spraying gelcoat with a preval sprayer, strain your gelcoat after it has been reduced and activated using a paper disposable strainer then disregard the plastic strainer attached to the straw from the preval sprayer. This will give you a heavier and more consistent spray. For over-all gelcoat refinishing use the same mix and steps as shown in the instructional instead of a preval sprayer, apply using an automotive spray gun, (no special tip needed). Gelcoat has to be thinned the same for a suction feed or gravity feed spray gun although using a gravity feed spray gun will leave more orange peel than necessary. To apply using a suction feed spray gun will give you a smoother surface as gelcoat is more atomized throwing a finer spray yet releasing most solvents when spraying with around 60lb psi with in line water separator, keep your spray gun moving to avoid a wrinkle in the gelcoat over lapping each coat. The heavier the coat is applied the more micro pin holes will exist; using a suction feed spray gun will give you a better quality finish over your Fibreglass repairs Gold Coast. Never spray gelcoat in direct sunlight during a hot day, the surface will skin too fast trapping solvents creating pin holes leaving a dull finish at job completion. Spraying gelcoat on the entire boat deck or hull be sure to prime first to cover all pin holes and repaired areas also to avoid blistering especially near the waterline, apply 4 coats at waterline and below, remember you will be sanding off at least a coat leaving you with 3 coats needed for a water bearier, 2 coats are fine for the rest of the vessel. Use Duratech vinylester primer some recommend polyester primer though it may be too brittle and eventually the primer may chalk beneath the sprayed gelcoat and chip or flake off easily. Using auto primers for a gelcoat refinish is a bad idea, spray at least 5 coats of gelcoat when re-surfacing a complete boat deck or hull. For gelcoat spot repair be sure to sand far past the repaired area to be sprayed to make sure your gelcoat spray does not exceed over the unsanded surface, use the proper grit for sanding during the final prep. To avoid a wave or warped finish at job completion, never use tape around the area, it may only create a step as overspray build up exceeds onto the tape. Let your polisher remove any fine overspray that traveled onto the Antifouling Gold Coast if any, if using tape or masking paper stay clear of the area to be sprayed at least a couple feet. Spraying true colors, red, blue, green etc. and your color is a bit off give a bigger blend line and spray 3 coats of clear gelcoat over the base color and 1 to 2 ft each side of your color blend. Let your gelcoat cure for at least 48 hours before sanding that will give you a better blend after polishing as the blend line will be much harder and thinner without breaking away leaving a Gelcoat repairs Gold Coast area invisible at all angles, using the proper gelcoat additives of course.
Related Articles -
antifouling gold coast, gelcoat repairs gold coast, boat detailing gold coast,
|
Rate This Article |
|
|
|
Do you Agree or Disagree? Have a Comment? POST IT!
Reader Opinions |
|
|
|
|
|
|
|
|
Author Login |
|
|
Advertiser Login
ADVERTISE HERE NOW!
Limited Time $60 Offer!
90 Days-1.5 Million Views
|
|
GENE MYERS
Author of four books and two screenplays; frequent magazine contributor. I have four other books "in...more
|
|
|
|
|
TIM FAY
After 60-plus years of living, I am just trying to pass down some of the information that I have lea...more
|
|
|
|
|
LAURA JEEVES
At LeadGenerators, we specialise in content-led Online Marketing Strategies for our clients in the t...more
|
|
|
|
|
ALEX BELSEY
I am the editor of QUAY Magazine, a B2B publication based in the South West of the UK. I am also the...more
|
|
|
|
|
SUSAN FRIESEN
Located in the lower mainland of B.C., Susan Friesen is a visionary brand strategist, entrepreneur, ...more
|
|
|
|
|
STEPHEN BYE
Steve Bye is currently a fiction writer, who published his first novel, ‘Looking Forward Through the...more
|
|
|
|
|
SHALINI MITTAL
A postgraduate in Fashion Technology. Shalini is a writer at heart! Writing for her is an expression...more
|
|
|
|
|
ADRIAN JOELE
I have been involved in nutrition and weight management for over 12 years and I like to share my kn...more
|
|
|
|
|
JAMES KENNY
James is a Research Enthusiast that focuses on the understanding of how things work and can be impro...more
|
|
|
|